![]() At the very end of this piece of added tubing, before it was installed, I drilled and attached one of the two caster wheels. I painted this piece of tubing the same color as the bicycle and it remains on the bike at all times. In order to move the pivot point between the bicycle and the trailer to a point where it would allow the trailer to turn from side to side as far as possible, I attached a 3/4" X 3/4" length of square channel steel tubing that fastens behind the main chainwheel of the bicycle, and is firmly clamped with several coaster brake frame clamps along the left chainstay to the left rear dropout (hub), and then extends past the rear dropout past the rear tire of the bike. I have a long wheelbase recumbent bicycle that already is difficult to turn in a tight radius - I did not want a trailer coupler that was not fully flexible and would not be able to allow my bicycle trailer to turn freely behind the bicycle. This is also a hardware store item and should cost less than $4.Īlthough many bike trailers attach to the left rear hub of the bicycle, this attachment point prohibits the trailer from turning a full 180 degrees around the rear of the bike. ![]() (5) Though purely optional, I wanted to be able to quickly attach and detach the bicycle trailer from the bike and therefore replaced one of the two caster wheel bolts with a similar diameter and length locking hitch pin that slips through the caster wheel bolt holes and the caster wheel bushing (see ring on top of this locking hitch pin inserted through the caster on the right side of the accompanying photo). I used the caster wheels as described in the following steps to attach the trailer coupler to both the mounting point on the bicycle and to the bicycle trailer. The trailer tongue is the black section of square tubing also shown in the same picture. I fabricated an extended mount on my bicycle (see step 2) that is shown as the red square tubing in the picture illustrating this step. (4) Appropriate hardware to attach the coupler both to your bicycle and to the trailer frame. I used eight 1/2" long 1/4" bolts and nylon-insert lock nuts to bolt the casters to the galvanized construction connector. (3) Sufficient short bolts and locking nuts to attach the caster to this frame. I purchased a heavy duty right angle galvanized construction connector (i.e., Simpson), readily available from local lumber yards or construction supply stores, also for less than $4. ![]() (2) A frame to attach these casters at right angles to each other. The parts you will need for this plan are simple: (1) Two swivel casters of sufficient size - I used 2" swivel casters that are available at local hardware or home improvement stores for about $4 apiece. The proposed plan allows this movement in the following ways: (1) one caster wheel is trimmed flush on one side to allow it to be bolted horizontally to a point on the bicycle, and then the caster wheel frame is again reattached to the wheel, allowing the caster to turn horizontally on the bicycle mounting point (2) the caster swivel on this first caster also allows the trailer tongue to move up and down vertically and (3) the caster swivel on the second caster allows the trailer tongue to "rotate/tip" from side to side during travel independent of the vertical angle of the bicycle. Although that proposed Instructable would work as suggested, it seemed to me that, with the investment in a second swivel caster mounted on a fixed frame at a 90 degree angle to the first swivel caster, you could very easily attain flexibility in all 3 planes of motion: (1) allowing horizontal turning side to side (2) allowing the trailer tongue to move vertically up and down and (3) allowing the trailer to "rotate" - to "tip" from side to side. I had seen a previous Instructable that relied on a single swivel caster to allow the bike trailer to turn from side to side and move up and down vertically, but then suggested a "pipe and sleeve" sort of coupler to allow trailer rotation (tilt). This Instructable will demonstrate how to build a coupler that can be used with a variety of bicycle trailers that will turn and rotate in all possible directions: up and down, side to side, and rotate to allow the trailer to "tip" from side to side during travel.
0 Comments
Leave a Reply. |